John Lewis Freezer JLFFW1811 User Manual

JLFFW1811  
JLSS1814  
JLFFW2012  
JLSS2015  
JLFFW2013  
Fridge-Freezer  
Instruction manual  
 
• The appliance is intended for keeping  
foodstuff and/or beverages in a normal  
household as explained in this instruction  
booklet.  
• Do not use a mechanical device or any  
artificial means to speed up the thawing  
process.  
• Do not use other electrical appliances (such  
as ice cream makers) inside of refrigerating  
appliances, unless they are approved for  
this purpose by the manufacturer.  
3. Make sure that you can come to the  
mains plug of the appliance.  
4. Do not pull the mains cable.  
5. If the power plug socket is loose, do not  
insert the power plug. There is a risk of  
electric shock or fire.  
6. You must not operate the appliance  
without the lamp cover of interior  
lighting.  
• This appliance is heavy. Care should be  
taken when moving it.  
• Do not remove nor touch items from the  
freezer compartment if your hands are  
damp/wet, as this could cause skin  
abrasions or frost/freezer burns.  
• Do not damage the refrigerant circuit.  
• The refrigerant isobutane (R600a) is  
contained within the refrigerant circuit of  
the appliance, a natural gas with a high level  
of environmental compatibility, which is  
nevertheless flammable.  
• Avoid prolonged exposure of the appliance  
to direct sunlight.  
During transportation and installation of  
the appliance, be certain that none of the  
components of the refrigerant circuit  
become damaged.  
If the refrigerant circuit should become  
damaged:  
Daily Use  
• Do not place hot items such as pans and  
baking trays near the plastic components of  
the appliance.  
• Do not store flammable gas and liquid in the  
appliance, because they may explode.  
• Do not place food products directly against  
the air outlet on the rear wall.1)  
• Frozen food must not be re-frozen once it  
has been thawed out.  
• Store pre-packed frozen food in  
accordance with the frozen food  
manufacturer's instructions.  
– avoid open flames and sources of ignition  
– thoroughly ventilate the room in which  
the appliance is situated  
• It is dangerous to alter the specifications or  
modify this product in any way. Any  
damage to the cord may cause a short-  
circuit, fire and/or electric shock.  
Warning! Any electrical component  
(power cord, plug, compressor) must  
be replaced by a certified service agent  
or qualified service personnel.  
• Appliance's manufacturers storage  
recommendations should be strictly  
adhered to. Refer to relevant instructions.  
• Do not place carbonated or fizzy drinks in  
the freezer compartment as it creates  
pressure on the container, which may  
cause it to explode, resulting in damage to  
the appliance.  
1. Power cord must not be lengthened.  
2. Make sure that the power plug is not  
squashed or damaged by the back of  
the appliance. A squashed or damaged  
power plug may overheat and cause a  
fire.  
1) If the appliance is Frost Free  
3
 
• Ice lollies can cause frost burns if consumed • The appliance must not be located close to  
straight from the appliance.  
radiators or cookers.  
• Make sure that the mains plug is accessible  
after the installation of the appliance.  
Care and cleaning  
• Before maintenance, switch off the  
appliance and disconnect the mains plug  
from the mains socket.  
Service  
• Any electrical work required to do the  
servicing of the appliance should be carried  
out by a qualified electrician or competent  
person.  
• Do not clean the appliance with metal  
objects.  
• Do not use sharp objects to remove frost  
from the appliance. Use a plastic scraper.  
• Regularly examine the drain in the  
refrigerator for defrosted water. If  
necessary, clean the drain. If the drain is  
blocked, water will collect in the bottom of  
the appliance.  
• This product must be serviced by an  
authorised Service Centre, and only  
genuine spare parts must be used.  
Environment Protection  
This appliance does not contain gasses  
which could damage the ozone layer,  
in either its refrigerant circuit or  
insulation materials. The appliance  
shall not be discarded together with  
the urban refuse and rubbish. The  
insulation foam contains flammable  
gases: the appliance shall be disposed  
according to the applicable regulations  
to obtain from your local authorities.  
Avoid damaging the cooling unit,  
especially at the rear near the heat  
exchanger. The materials used on this  
appliance marked bythe symbol are  
recyclable.  
Installation  
Important! For electrical connection  
carefully follow the instructions given in  
specific paragraphs.  
• Unpack the appliance and check if there are  
damages on it. Do not connect the  
appliance if it is damaged. Report possible  
damages immediately to the place you  
bought it. In that case retain packing.  
• It is advisable to wait at least four hours  
before connecting the appliance to allow  
the oil to flow back in the compressor.  
• In order to prevent over heating there must  
be adequate circulation around the  
appliance.  
• Please refer to the correct positioning and  
location instructions that can be found in  
the Installation section of this user guide.  
4
 
Contents  
For the user  
For the installer  
Safety information  
2
6
Technical data  
20  
Product description  
Installation  
Positioning  
Location  
Electrical Connection  
Permanent connection  
Rear spacers  
20  
20  
20  
21  
22  
22  
22  
22  
23  
23  
Control panel  
Display  
First switch on  
Switching off  
Functions Menu  
Temperature regulation  
Holiday Function "H"  
Ambient Temperature Function  
Child Lock Function  
Shopping Function  
Eco Mode Function  
Action Freeze Function  
Drinks Chill Function  
Excessive temperature alarm  
7
7
8
8
8
8
8
9
9
9
9
9
10  
10  
Levelling  
Removing the shelf holders  
Installation of the carbon air filter  
Door reversibility  
Repairs - after sales service  
Environmental concerns  
26  
27  
First use  
Cleaning the interior  
11  
11  
Daily use  
11  
11  
11  
11  
11  
12  
12  
12  
13  
Storage of frozen food  
Thawing  
Carbon Air Filter  
Movable shelves  
Bottle rack  
Vegetable Drawer  
Positioning the door shelves  
Chiller Zone  
Guide to use the  
instruction manual  
The following symbols will be found in the text  
to guide you throughout the instructions:  
Removaloffreezingbasketsfromthefreezer 14  
Helpful hints and tips  
14  
Safety instructions  
Hints and tips  
Care and cleaning  
Periodic cleaning  
Replacing the carbon air filter  
Defrosting  
16  
16  
16  
17  
Environmental information  
What to do if…  
17  
5
 
Product description  
1
22  
14  
15  
2
3
4
16  
17  
5
6
18  
20  
21  
7
8
19  
9
10  
11  
12  
13  
23  
24  
25  
A - Refrigerator  
B - Freezer  
1 Control panel  
13 Adjustable feet  
14 Dairy compartment  
15 Egg tray  
2 Air distribution and light box  
3 Glass shelves  
4 Bottle rack  
16 Door shelf  
17 Door gasket  
18 Bottle shelf  
5 Glass shelf  
19 Handles  
6 Chiller Zone compartment  
7 Salad/vegetable drawer  
8 Rating plate  
20 Condenser  
21 Defrost water outlet tube  
22 Spacers  
9 Air grid  
23 Evaporator tray  
24 Compressor  
25 Rollers  
10 Storing compartment(s)  
11 Quick freeze drawer  
12 Bottom plinth  
6
 
Control panel  
A B  
C
D E  
A - Appliance button ON/OFF  
D - Function button  
B - Temperature regulation button  
C - Temperature and function indicator  
E - Confirmation button  
Display  
Indicates the compartment is on.  
Child Lock function indicator.  
Timer function indicator.  
Indicates the temperature of the  
relevant compartment.  
If it flashes the operations corresponds  
to the relative compartment.  
Shopping function indicator.  
Excessive temperature alarm.  
Drinks Chill function indicator.  
Action Freeze function indicator.  
If on the indicated temperature is the  
ambient temperature.  
Positive or negative temperature  
indicator.  
Eco mode function indicator.  
Temperature indicator.  
7
 
The following functions are indicated:  
Select/Switch off/Switch on fridge  
compartment  
Select/Switch off/Switch on freezer  
compartment  
First switch on  
After plugging the plug into the power outlet,  
if the display is not illuminated, press key (A),  
appliance on.  
As soon as the appliance is turned on, it is in  
alarm condition, the temperature flashes and  
you will hear a buzzer.  
Press key (E) and the buzzer will go off (also  
see the section on "excessive temperature  
Ambient Temperature  
Child Lock function  
Shopping function  
Eco Mode function  
Action Freeze function  
Drinks Chill function  
alarm" ) the icon  
still flashes and on the  
indicator will appear the warmest  
temperature reached.  
Temperature regulation  
For a correct storage of the food select the  
Eco mode function that guarantee the  
following temperatures are set:  
+5°C in the fridge  
The temperature may be regulated by  
pressing the key (D) to select the  
compartment and than the key (B) to set the  
desired temperature.  
-18°C in the freezer  
By pressing the key (B) the current  
temperature setting flashes on the indicator.  
To confirm the choice of the temperature  
press the key (E).  
• Wait until the inside compartment  
temperature reach -18°C, before  
introducing the goods in the freezer  
compartment.  
You will hear the buzzer for few seconds and  
the indicator displays the newly selected  
temperature for a few seconds, then shows  
again the inside compartment temperature.  
The newly selected-temperature must be  
reached after 24 hours.  
After a long period out of use it is not  
necessary to set again the temperature  
because it remains stored.  
• To select a different temperature see  
"Temperature regulation".  
Important!If the door remains ajar for some  
minutes, the internal lighting will turn off  
electronically; after this, the lighting function  
will be reset by closing and opening the door  
itself.  
Switching off  
Important!During thestabilityperiodbythe  
first starting the temperature displayed can  
not correspond to the setting temperature.  
During this time it is possible that the  
temperature displayed is different than the  
setting temperature.  
The appliance is shut off by pressing button  
(A) until a countdown from -3 -2 -1 is  
completed.  
Functions Menu  
By activating the key (D) the functions menu  
is operating. Each function could be confirmed  
by pressing button (E). If there is no  
confirmation after some seconds the display  
will go out from the menu and return in  
normal condition.  
Holiday Function "H"  
The holiday function sets the temperature at  
+ 15°C.  
8
 
This function allows you to keep the  
refrigerator shut and empty during a long  
holiday period ( e. g. the summer holidays)  
without the formation of a bad smell.  
To turn on the holiday function operate as per  
modift the selected temperature. The  
temperature indicator can modify the  
displayed temperature up to + 8 °C, 1 °at a  
tim. + 2 °C will be followed by the letter "H  
". Press key E to confirm.  
It is possible to de-activate the function at any  
time by pressing key (D) until the  
corresponding icon will flash and then key (E).  
Shopping Function  
If you need to insert a large amount of warm  
food, for example after doing the grocery  
shopping, we suggest activating the Shopping  
function to chill the products more rapidly and  
to avoid warming the other food which is  
already in the refrigerator.  
Now the refrigerator is in the "holiday  
"function in the energy- saving mode.  
The Shopping function is activated by pressing  
key (D) (several times if necessary) until the  
corresponding icon appears . You must  
confirm the choice by pressing key (E) within  
few seconds. You will hear the buzzer and the  
icon remains lighted.  
The Shopping function shuts off automatically  
after approximately 6 hours. It is possible to  
de-activate the function at any time by  
pressing key (D) until the corresponding icon  
will flash and then key (E).  
Important! The fridge compartment must  
be empty with holiday function on.  
Ambient Temperature  
Function  
The ambient temperature function is  
activated by pressing key (D) (several times if  
necessary) until the corresponding icon  
appears  
. In this condition the displayed  
temperature is the ambient temperature.  
You must confirm the choice by pressing key  
(E) within few seconds. You will hear the  
buzzer and the icon remains lighted.  
It is possible to de-activate the function at any  
time by pressing key (D) until the  
Eco Mode Function  
The Eco Mode function is activated by  
pressing key (D) (several times if necessary)  
until the corresponding icon appears  
You must confirm the choice by pressing key  
(E) within few seconds. You will hear the  
buzzer and the icon remains lighted.  
corresponding icon will flash and then key (E)  
In this condition the chosen temperatures are  
automatically set (+ 5°C and - 18°C), in the  
best conditions for storing food.  
It is possible to de-activate the function at any  
time by changing the selected temperature in  
one of the compartment.  
Child Lock Function  
The Child Lock function is activated by  
pressing key (D) (several times if necessary)  
until the corresponding icon appears  
.
You must confirm the choice by pressing key  
(E) within few seconds. You will hear the  
buzzer and the icon remains lighted. In this  
condition any possible operation through the  
keys does not cause any change as long as this  
function is activated.  
Action Freeze Function  
The freezer compartment is suitable for long  
term storage of commercially frozen and  
deep-frozen food, and for freezing fresh food.  
9
 
The maximum quantity of foods to freeze in  
24 hours is shown on the rating plate.  
To freeze the amount of food indicated on the  
rating plate, place the food directly in touch  
with the cooling surface (remove the drawer  
or basket). In case the food is frozen inside the  
drawers or baskets, the maximum quantity is  
slightly reduced.  
To freeze fresh foods, you will need to  
activate the Action Freeze function. Press key  
(D) (several times if necessary) until  
indicator appears.  
You must confirm the choice by pressing key  
(E) within few seconds. You will hear the  
buzzer and on the display will appear some  
animation with lines.  
After a pre-cooling period of 24 hours, place  
the foods in the freezer.  
Place the food to be frozen in the  
compartment, as this is the coldest point.  
The freezing process takes 24 hours. During  
this period do not put other foods in the  
freezer.  
This function stops automatically after 52  
hours.  
It is possible to deactivate the function at any  
At the end of the selected time there are the  
following indications:  
• on the indicator  
the symbol flashing  
the icon  
flashing  
• the icon flashing  
• sounding of an acoustic alarm until key (E)  
is pressed  
At this point bear in mind to remove the  
drinks contained in the freezer compartment.  
It is possible to deactivate the function at any  
time by pressing key (D) until the  
corresponding icon will flash and then key (E).  
Excessive temperature  
alarm  
An increase in the temperature in a  
compartment (for example due to an power  
failure) is indicated by:  
• flashing temperature  
freezer compartment flashing  
• flashing of the icon  
• sounding of buzzer  
When normal conditions are restored:  
• the acoustic signal shuts off  
• the temperature value continues to flash  
When you press key (E) to de-activate the  
alarm, the highest temperature reached in the  
time by pressing key (D) until  
flash and then press key (E).  
indicator will  
Drinks Chill Function  
compartment appears on indicator  
some seconds.  
for  
The Drinks Chill function is to be used as a  
safety warning when placing bottles in the  
freezer compartment. It is activated by  
pressing key (D) (several times if necessary)  
Then it returns on the normal operation  
showing the temperature of the selected  
compartment.  
During the alarm phase, the buzzer can be  
switched off by pressing key (E).  
until the corresponding icon appears  
.
You must confirm the choice by pressing key  
(E) within few seconds. You will hear the  
buzzer and the icon remains lighted.  
In this condition it operates a timer with a  
default value of 30 min. and it could change  
from 1 to 90 min., by pressing key (B) you  
select the minutes needed.  
10  
 
First use  
Important! Do not use detergents or  
abrasive powders, as these will damage the  
finish.  
Cleaning the interior  
Before using the appliance for the first time,  
wash the interior and all internal accessories  
with lukewarm water and some neutral soap  
so as to remove the typical smell of a brand-  
new product, then dry thoroughly.  
Daily use  
Storage of frozen food  
Carbon Air Filter  
When first starting-up or after a period out of Your appliance is equipped with a carbon filter  
use, before putting the products in the  
behind a flap in the rear wall of the air  
compartment let the appliance run at least 2 distributing box.  
hours on the higher settings.  
The filter purifies the air from unwanted  
odours in the fridge compartment meaning  
that the storage quality will be further  
improved.  
Important! In the event of accidental  
defrosting, forexample due toa powerfailure,  
if the power has been off for longer than the  
value shown in the technical characteristics  
Important! During the operation, always  
chart under "rising time", the defrosted food keep the air ventilation flap closed.  
must be consumed quickly or cooked  
immediately and then re-frozen (after  
cooling).  
Thawing  
Deep-frozen or frozen food, prior to being  
used, can be thawed in the refrigerator  
compartment or at room temperature,  
depending on the time available for this  
operation.  
Small pieces may even be cooked still frozen,  
directly from the freezer: in this case, cooking  
will take longer.  
Movable shelves  
The walls of the refrigerator are equipped  
with a series of runners so that the shelves can  
be positioned as desired.  
Download from Www.Somanuals.c1om1. All Manuals Search And Download.  
There is a separator inside the drawer that can  
be placed in different positions to allow for the  
subdivision best suited to personal needs.  
There is a grille (if foreseen) on the bottom of  
the drawer to separate the fruit and  
vegetables from any humidity that may form  
on the bottom surface.  
All parts inside the drawer can be removed  
for cleaning purposes  
1
2
Bottle rack  
Place the bottles (with the opening facing  
front) in the pre-positioned shelf.  
Important! If the shelf is positioned  
horizontally, place only closed bottles.  
This bottle holder shelf can be tilted in order  
to store previously opened bottles. To obtain  
this result, pull the shelf up so it can rotate  
upwards and be placed on the next higher  
level.  
Positioning the door  
shelves  
To permit storage of food packages of various  
sizes, the door shelves can be placed at  
different heights.  
To make these adjustments proceed as  
follows:  
gradually pull the shelf in the direction of the  
arrows until it comes free, then reposition as  
required.  
Vegetable Drawer  
The drawer is suitable for storing fruit and  
vegetables.  
12  
 
5
6
Chiller Zone  
2
The Chiller Zone compartment is suitable for  
storing fresh food like fish, meat, seafood,  
because the temperature is lower here than  
in the rest of the fridge. It is placed in the lower  
part of the refrigerator, directly above of the  
vegetable drawer.  
3
1. Open the door of the refrigerator as wide  
as possible. If you cannot open the door  
at an angle of 180° because of a limit stop  
or any other objects , remove the bottle  
shelf from the door.  
If you wish to remove the Chiller Zone  
compartment, do these steps:  
2. Pull the drawer towards yourself to the  
end point.  
3. Slightly lift the front part of the drawer.  
4. Remove the drawer from its support.  
5. Lift the back of the support from its nest.  
6. Pull the frame towards yourself.  
7. Remove the support frame.  
To put the Chiller Zone compartment to its  
initial position, do above steps in opposite  
sequence.  
Download from Www.Somanuals.c1om3. All Manuals Search And Download.  
Removal of freezing  
baskets from the freezer  
The freezing baskets have a limit stop to  
prevent their accidental removal or falling out.  
At the time of its removal from the freezer,  
pull the basket towards yourself and, upon  
reaching the end point, remove the basket by  
tilting its front upwards.  
At the time of putting it back, slightly lift the  
front of the basket to insert it into the freezer.  
Once you are over the end points, push the  
baskets back in their position.  
2
1
Helpful hints and tips  
• When the compressor is on, the refrigerant  
is being pumped around and you will hear  
a whirring sound and a pulsating noise from  
the compressor. This is correct.  
• The thermic dilatation might cause a  
sudden cracking noise. This is not a fault  
with the appliance and is a completely  
normal operating sound.  
Normal Operating  
Sounds  
• You may hear a faint gurgling and a bubbling  
sound when the refrigerant is pumped  
throughthe coils or tubing. This is notafault  
with the appliance and is a completely  
normal operating sound.  
14  
 
Milk bottles: these should have a cap and  
should be stored in the bottle rack on the  
door.  
Bananas, potatoes, onions and garlic, if not  
packed, must not be kept in the refrigerator.  
Hints for energy saving  
• Do not open the door frequently or leave  
it open longer than absolutely necessary.  
• If the ambient temperature is high and the  
Temperature Regulator is set to low  
temperature and the appliance is fully  
loaded, the compressor may run  
continuously, causing frost or ice on the  
evaporator. If this happens, set the  
Temperature Regulator towards a warmer  
setting to allow automatic defrosting and  
will therefore save in electricity  
Hints for freezing  
To help you make the most of the freezing  
process, here are some important hints:  
• the maximum quantity of food which can  
be frozen in 24 hrs. is shown on the rating  
plate;  
consumption.  
• the freezing process takes 24 hours. No  
further food to be frozen should be added  
during this period;  
• only freeze top quality, fresh and  
thoroughly cleaned, foodstuffs;  
• prepare food in small portions to enable it  
to be rapidly and completely frozen and to  
make it possible subsequently to thaw only  
the quantity required;  
• wrap up the food in aluminium foil or  
polythene and make sure that the packages  
are airtight;  
Hints for fresh food  
refrigeration  
To obtain the best performance:  
• do not store warm food or evaporating  
liquids in the refrigerator  
• do cover or wrap the food, particularly if it  
has a strong flavour  
• position food so that air can circulate freely  
around it  
• do not allow fresh, unfrozen food to touch  
food which is already frozen, thus avoiding  
a rise in temperature of the latter;  
Hints for refrigeration  
Useful hints:  
• lean foods store better and longer than  
fatty ones; salt reduces the storage life of  
food;  
Meat (all types) : wrap in polythene bags and  
place on the glass shelf above the vegetable  
drawer.  
For safety, store in this way only one or two • it is advisable to show the use by date on  
days at the most.  
each individual pack to enable you to keep  
tab of the storage time.  
Cooked foods, cold dishes, etc.: these should  
be covered and may be placed on any shelf.  
Fruit and vegetables: these should be  
thoroughly cleaned and placed in the special  
drawer(s) provided.  
Butter and cheese: these should be placed in  
special airtight containers or wrapped in  
aluminium foil or polythene bags to exclude as  
much air as possible.  
Warning! Lolly ices, if consumed  
immediately after removal from the  
freezer compartment can cause  
freezer burns.  
Download from Www.Somanuals.c1om5. All Manuals Search And Download.  
• not open the door frequently or leave it  
open longer than absolutely necessary.  
• Once defrosted, food deteriorates rapidly  
and cannot be refrozen.  
• Donotexceedthestorage periodindicated  
by the food manufacturer.  
Hints for storage of  
frozen food  
To obtain the best performance from this  
appliance, you should:  
• make sure that the commercially frozen  
foodstuffs were adequately stored by the  
retailer;  
• be sure that frozen foodstuffs are  
transferred from the foodstore to the  
freezer in the shortest possible time;  
Care and cleaning  
Clean the condenser (black grill) and the  
Caution! Unplug the appliance  
before carrying out any maintenance  
operation.  
compressor at the back of the appliance with  
a brush or a vacuum cleaner. This operation  
will improve the performance of the appliance  
and save electricity consumption.  
This appliance contains hydrocarbons  
in its cooling unit; maintenance and  
recharging must therefore only be  
carried out by authorised technicians.  
Important! Take care of not to damage the  
cooling system.  
Many proprietary kitchen surface cleaners  
contain chemicals that can attack/damage the  
plastics used in this appliance. For this reason  
it is recommended that the outer casing of this  
appliance is only cleaned with warm water  
with a little washing-up liquid added.  
After cleaning, reconnect the equipment to  
the mains supply.  
Periodic cleaning  
The equipment has to be cleaned regularly:  
• clean the inside and accessories with  
lukewarm water and some neutral soap.  
• regularly check the door seals and wipe  
clean to ensure they are clean and free from  
debris.  
• rinse and dry thoroughly.  
Replacing the carbon air  
filter  
To get the best performance the carbon air  
filter should be changed once every year.  
New active air filters can be purchased from  
your local dealer.  
Important! Do not pull, move or damage  
any pipes and/or cables inside the cabinet.  
Never use detergents, abrasive powders,  
highly perfumed cleaning products or wax  
polishes to clean the interior as this will  
damage the surface and leave a strong odour.  
Refer to "Installation of the carbon air filter"  
for the instructions.  
16  
 
The absence of frost is due to the continuous  
circulation of cold air inside the compartment,  
driven by an automatically controlled fan.  
Defrosting  
Your appliance is frost free. This means that  
there is no build up of frost when it is in  
operation, neither on the internal walls nor on  
the foods.  
What to do if…  
Caution! Before troubleshooting,  
disconnect the power supply.  
Only a qualified electrician or  
competent person must complete any  
repairs to the appliance.  
Important! It is normal to hear some  
operating noises during use (for example the  
compressor, refrigerant circulation).  
Problem  
Possible cause  
Solution  
The appliance is noisy.  
The appliance is not supported  
properly.  
Check if the appliance stands stable  
(all the four feet should be on the  
floor).  
The compressor  
operates continually.  
The Temperature regulator may Set a warmer temperature.  
be set incorrectly.  
The door is not closed correctly. Refer to "Closing the door".  
The door has been opened too  
frequently.  
Do not keep the door open longer  
than necessary.  
The product temperature is too Let the product temperature  
high.  
decrease to room temperature  
before storage.  
The room temperature is too  
high.  
Decrease the room temperature.  
The Action Freeze function is  
switched on.  
Refer to "Action Freeze function".  
Water flows on the rear During the automatic defrosting This is correct.  
plate of the refrigerator. process, frost defrosts on the rear  
plate.  
Water flows into the  
refrigerator.  
The water outlet is clogged.  
Clean the water outlet.  
Products prevent that water flows Make sure that products do not  
into the water collector. touch the rear plate.  
Download from Www.Somanuals.c1om7. All Manuals Search And Download.  
Problem  
Possible cause  
Solution  
Water flows on the  
ground.  
The melting water outlet does not Attach the melting water outlet to  
flow in the evaporative tray above the evaporative tray.  
the compressor.  
There is too much frost Products are not wrapped  
and ice.  
correctly..  
Please refer to the "Hints for  
refrigeration" and "Hints for  
freezing" instructions in this guide.  
The door is not closed correctly. Refer to "Closing the door".  
The Temperature regulator may Set a higher temperature.  
be set incorrectly.  
The temperature in the The door is not closed correctly. Refer to "Closing the door".  
appliance is too high.  
The product temperature is too Let the product temperature  
high.  
decrease to room temperature  
before storage.  
Many products are stored at the Store less products at the same  
same time. time.  
The temperature in the There is no cold air circulation in Make sure that there is cold air  
refrigeration is too high. the appliance.  
circulation in the appliance.  
The temperature in the Products are too near to each  
Store products so that there is cold  
air circulation.  
freezer is too high.  
other.  
The appliance does not The appliance is switched off.  
Switch on the appliance.  
operate.  
The mains plug is not connected Please refer to the installation  
to the mains socket correctly.  
instructions provided in this user  
guide.  
The appliance has no power.  
To test this connect a different  
There is no voltage in the mains electrical appliance to the mains  
socket.  
socket. Contact a qualified  
electrician.  
The lamp does not work. The lamp is defective.  
Refer to "Replacing the lamp".  
If after following these instructions you do not 2. Remove the lamp cover.  
resolve the fault with your appliance please  
refer to the "Repairs - After Sales Service".  
3. Replace the lamp with one of the same  
power (the maximum power is shown on  
the light bulb cover).  
Replacing the lamp  
4. Install the lamp cover.  
5. Connect the plug to the mains socket.  
6. Open the door. Make sure that the light  
comes on.  
Caution! Disconnect the plug from  
the mains socket.  
1. Pull outwards the hook of the lamp cover.  
18  
 
1
2
Closing the door  
1. Clean the door gaskets.  
2. If necessary, adjust the door. Refer to  
"Installation".  
3. If necessary, replace the defective door  
gaskets. Contact the Service Force  
Center.  
Download from Www.Somanuals.c1om9. All Manuals Search And Download.  
Technical data  
JLFFW1811  
JLSS1814  
JLFFW2013  
JLSS2015  
JLFFW2012  
Dimension  
Height  
Width  
Depth  
1850 mm  
595 mm  
632 mm  
16 h  
2010 mm  
595 mm  
632 mm  
16 h  
2010 mm  
595 mm  
632 mm  
16 h  
Rising Time  
The technical information are situated in the  
rating plate on the internal left side of the  
appliance and in the energy label.  
Installation  
Read the "Safety Information" carefully  
for your safety and correct operation  
of the appliance before installing the  
appliance.  
Location  
The appliance should be installed well away  
from sources of heat such as radiators,  
boilers, direct sunlight etc. Ensure that air can  
circulate freely around the back of the cabinet.  
To ensure best performance, if the appliance  
is positioned below an overhanging wall unit,  
the minimum distance between the top of the  
cabinet and the wall unit must be at least 100  
mm . Ideally, however, the appliance should  
not be positioned below overhanging wall  
units. Accurate levelling is ensured by one or  
more adjustable feet at the base of the  
cabinet.  
Positioning  
Install this appliance at a location where the  
ambient temperature corresponds to the  
climate class indicated on the rating plate of  
the appliance:  
Climate Ambient temperature  
class  
SN  
N
+10°C to + 32°C  
+16°C to + 32°C  
+16°C to + 38°C  
+16°C to + 43°C  
ST  
T
20  
 
Warning! It must be possible to  
disconnect the appliance from the  
mains power supply; the plug must  
therefore be easily accessible after  
installation.  
Green and Yellow:  
Brown:  
Earth  
Live  
1
3
5
Blue:  
Neutral  
As the colours of the wires in the mains lead  
of this appliance may not correspond with the  
coloured markings identifying the terminals in  
your plug, proceed as follows:  
1. Connect the wire coloured green and  
yellow to the terminal marked either with  
the letter “E“ or by the earth symbol  
or coloured green and yellow.  
Electrical Connection  
Caution! Any electrical work  
required to install this appliance should  
be carried out by a qualified electrician  
or competent person.  
Warning! This appliance must be  
earthed.  
The manufacturer declines any liability  
should these safety measures not be  
observed.  
2. Connect the wire coloured blue to the  
terminal either marked with the letter  
“N“ or coloured black.  
3. Connect the wire coloured brown to the  
terminal either marked with the “L“ or  
coloured red.  
Important! The wires in the mains lead are  
coloured in accordance with the following  
code:  
4. Check that no cut, or stray strands of wire  
4
is present and the cord clamp is secure  
over the outer sheath.  
5. Make sure the electricity supply voltage is  
the same as that indicated on the  
appliance rating plate.  
6. Switch on the appliance.  
Download from Www.Somanuals.c2om1. All Manuals Search And Download.  
The appliance is supplied with a 13 amp plug  
Levelling  
When placing the appliance ensure that it  
stands level. This can be achieved by two  
adjustable feet at the bottom in front.  
2
fitted . In the event of having to change the  
fuse in the plug supplied, a 13 amp ASTA  
approved (BS 1362) fuse must be used.  
Warning! A cut off plug inserted into  
a 13 amp socket is a serious safety  
(shock) hazard. Ensure that it is  
disposed of safely.  
Permanent connection  
In the case of permanent connection it is  
necessary that you install a double pole switch  
between the appliance and the electricity  
supply (mains), with a minimum gap of 3mm  
between the switch contacts and of a type  
suitable for the required load in compliance  
with the current electrical regulations.  
The switch must not break the green and  
yellow earth cable at any point.  
Removing the shelf  
holders  
Rear spacers  
In the bag with the documentation, there are  
two spacers which must be fitted as shown in  
the figure.  
Slacken the screws and insert the spacer  
under the screw head, then tighten again the  
screws.  
Your appliance is equipped with shelf  
retainers that make it possible to secure the  
shelves during transportation.  
To remove them proceed as follows:  
1. Move the shelf holders in the direction of  
the arrow (A).  
2. Raise the shelf from the rear and push it  
forward until it is freed (B).  
3. Remove the retainers (C).  
22  
 
A
B
C
Important! During operation, always keep  
the air ventilation flap closed.  
The filter should be handled carefully so  
fragments do not loosen from the surface.  
Installation of the carbon  
air filter  
Door reversibility  
The carbon air filter is an active carbon filter  
which absorbs bad odours and permits to  
maintain the best flavour and aroma for all  
foodstuffs without risk of odour cross  
contamination.  
On delivery the carbon filter is in a plastic bag  
to maintain it’s duration and characteristics.  
The filter should be placed behind the flap  
before the appliance is turned on.  
Warning! Before carrying out any  
operations, remove the plug from the  
power socket.  
Important! To carry out the following  
operations, we suggest that this be made with  
another person that will keep a firm hold on  
the doors of the appliance during the  
operations.  
1. Open the flap cover (1)  
To change the opening direction of the door,  
do these steps:  
1. Open the door with the appliance in the  
upright position. Unscrewthe screws (t1)  
and remove the upper door plastic trim  
(t2). Close the door.  
2. Remove the filter from the plastic bag  
3. Insert the filter in the slot found in the back  
of the flap cover (2)  
4. Close the flap cover  
Download from Www.Somanuals.c2om3. All Manuals Search And Download.  
t1  
t1  
d1  
t1  
t2  
t3  
d7  
6. Unscrew the middle hinge (m2). Remove  
the plastic spacer (m1).  
2. Remove the little plastic cover from the  
door plastic trim and refit on the opposite  
side (t3).  
3. Remove the panel (t4). If it is necessary  
use a screwdriver very carefully. Unscrew  
the screw on the other side. Remove the  
upper door mount (t5) . Place them in an  
empty plastic bag.  
m1  
m5  
m2  
m6  
m4  
m3  
t4  
t5  
7. Remove the spacer (m6)and move to the  
other side of the hinge pivot (m5).  
8. Remove the lower door.  
9. Remove using a tool the cover (b1).  
Unscrew the lower hinge pivot (b2) and  
the spacer (b3) and place them on the  
opposite side.  
10. Re-insert the cover (b1) on the opposite  
side.  
4. Remove the upper door.  
5. Unscrew the screw and remove the door  
stopper (d1). Attach it reversed on the  
other side.  
24  
 
16. Fit the pin of the middle hinge (m5) into  
the left-hand hole of the lower door.  
b1  
17. Re-insert the lower door on the pivot pin  
(b2).  
18. Re-screw the middle hinge (m1) on the  
opposite side . Do not forget the plastic  
spacer (m2) inserted under the middle  
hinge.  
19. Re-insert the upper door on the middle  
hinge (m5).  
b2  
Make sure that the edges of the doors run  
parallel to the side edge of the appliance.  
b3  
20. Position and fix the upper hinge (you can  
find them in the instruction for use bag)  
on the opposite side (t6).  
11. Disassemble the door locking elements  
(d2,d3) by unscrewing the screw (d4) .  
d2  
d4  
d3  
d6  
d5  
21. Insert the panel (t7) (that can be found in  
the instruction for use bag).  
22. Open the upper door, attach the top  
cover (t2) using screws (t1). Insert the  
magnet (d7). Close the door.  
23. Reposition, level the appliance, wait for  
at least four hours and then connect it to  
the power socket.  
12. Remove stoppers in both doors (d5,d6) .  
13. Reverse the door locking elements  
(d2,d3) , move to the other side of the  
other door and fix by screwing in the  
screw (d4) .  
14. Re-insert the stoppers (d5,d6) on the  
other side of the doors.  
24. Unscrew the handles (h1) and fix them on  
the opposite side.  
15. Remove the left-hand cover pin of the  
middle hinge (m3,m4) and move to the  
other side.  
Download from Www.Somanuals.c2om5. All Manuals Search And Download.  
• All screws are tightened.  
• The magnetic seal adheres to the cabinet.  
• The door opens and closes correctly.  
If the ambient temperature is cold (i.e. in  
Winter), the gasket may not fit perfectly to the  
cabinet. In that case, wait for the natural fitting  
of the gasket.  
h1  
In case you do not want to carry out the above  
mentioned operations, contact the nearest  
After Sales Service Force. The After Sales  
Service specialist will carry out the reversibility  
of the doors at your cost.  
Do a final check to make sure that:  
Repairs - after sales service  
Your appliance comes with a three year  
warranty. If it is not working correctly; consult  
the fault finding guides within this instruction  
book (Something not working). If a fault  
occurs which you can not resolve through  
following the advice and information  
contained within this instruction manual, the  
next step is to contact our extended warranty  
administrators on:  
5. The model and serial number of the  
appliance. So that you always have these  
numbers at hand, we recommend you to  
make a note of them here:  
• Mod.......................................  
• P.N.C.....................................  
• S.N.........................................  
IMPORTANT : If you call out an  
engineer to a fault listed below, or to  
repair a fault caused by incorrect use  
or installation, a charge will be made  
even if the appliance is under  
guarantee.  
0844 871 7771  
They will give you details for your local Service  
engineer. Before calling out an engineer,  
please ensure you have read the details under  
the heading “Something not working”.  
When you contact your local service engineer  
you will need to give the following details:  
1. Your name, address and post code  
2. Your telephone number  
3. Clear and concise details of fault  
4. The purchase date as found on your  
receipt  
Spare parts  
Always insist on genuine spare parts.  
An authorised service engineer should service  
this product, and only genuine spare parts  
should be used. Under no circumstances  
should you attempt to repair the appliance  
yourself. Repairs carried out by inexperienced  
persons may cause injury or serious  
26  
 
malfunctioning. Contact your local John Lewis  
branch.  
Environmental concerns  
The symbol  
on the product or on its  
packaging indicates that this product may not  
be treated as household waste. Instead it  
should be taken to the appropriate collection  
point for the recycling of electrical and  
electronic equipment. By ensuring this  
product is disposed of correctly, you will help  
prevent potential negative consequences for  
the environment and human health, which  
could otherwise be caused by inappropriate  
waste handling of this product. For more  
detailed information about recycling of this  
product, please contact your local council,  
your household waste disposal service or the  
shop where you purchased the product.  
Download from Www.Somanuals.c2om7. All Manuals Search And Download.  
John Lewis Partnership  
171 Victoria Street  
London SW1E 5NN  
210620342-UK-00-17042009  
925034086  
925034087  
925034270  
925034271  
925034272  
 

Infinity Portable Speaker MTS Center User Manual
Intel Computer Hardware Raptor AT User Manual
Intel Network Card IQ80332 User Manual
Invacare Mobility Aid P9000 XDT User Manual
IOGear GPS Receiver GME225BKIT User Manual
Jenn Air Microwave Oven JMC8100AD User Manual
Jenn Air Oven JJW8430DDB User Manual
JVC Portable Speaker SX LT55MK2 User Manual
Kenwood Stereo System DC 20 User Manual
KitchenAid Microwave Oven W10677488A User Manual